Computer Automation Technology

CAT-260 Repeater Controller

The CAT-260 is a direct replacement for the very popular CAT-250 with an enhanced vocabulary word list and a super accurate clock backed up with a coin cell battery. The CAT-260 provides sophisticated remote base and or link operation at an extremely affordable priced at $349.00.

 

CAT260 PCB

 

Features Include

Dual DTMF Decoders Internet Firmware Upgrades
TI Voice Synthesizer Forty (40) User Macros
Twenty Programmable Messages Fifty (50) Event Macros
 Real Time Clock CW Identifier
 Twenty (20) Position Scheduler Four (4) Logic Inputs
 Forty Two (42) Control Functions Six (6) Output Switches
 DTMF Audio Muting Fan Control Output
 DTMF Pad Test Optional Configuration Editor
 Remote Base Port Clock +/- 1 Min per Year

 

Voice Synthesizer
A [470] word vocabulary carefully selected for amateur repeater operation is available to construct [20] different voice messages. Each message can be [15] words in length. Configure your repeater ID and announcements to suit your particular needs and also have available general purpose messages .

 

DTMF Key-Pad Test
The key-pad test, available from both ports, will read back the numbers decoded in a synthesized voice. This includes the words "STAR" and "POUND".

 

Courtesy Tones
The CAT-260 provides individual courtesy tones for both the repeater and remote base inputs. Different courtesy tones can be selected to indicate port activity.

 

CW ID
The CAT-260 will switch to a CW ID when a user talks over the voice ID.

 

Repeater Timers
Twelve timers control repeater operation. Each timer is user programmable to afford maximum flexibility to suit your requirements. They are: System ID Timer, System Pending ID Timer, Port #1 and Port #2 Timeout Timers, Programming Length Timer, DTMF Access Sleep Timer, Port #2 Disconnect/ Connect Timer, COR drop to courtesy beep timer and Courtesy beep to transmitter drop timer, Pre-Voice Delay Timer, Turn on Delay Timer, and DTMF Muting Timer.

 

Link Transceiver Control
The CAT-260 offers full control of the link port. You can turn the link transceiver on and off, through the repeater or remote base port. Separate codes are available for each on/off function.

 

Computer Interface
The CAT-260, includes a RS-232 port. With the ED260W editor, this port is used to upload new firmware updates available on the C.A.T. website at catauto.com. You never need to change ROMs again. This RS-232 port is also used to upload a new program prepared by the CAT-260 Editor.

 

 Windows® Editor Program
The optional editor program provided on CDROM is used to manage the data file. The editor will work with any computer using a windows® XP, WIN7, WIN8, WIN10 (or greater) operating system. Use the program to display and make changes to the CAT-260 memory. Once changed, the memory can be up loaded into the controller.

 

DTMF Decoders
Two DTMF decoders, one for each port, insures reliable decoding of control and programming commands.

 

Port Configuration
Configure Port #2 as a simplex transceiver or Duplex transceiver port.

 

Logic Inputs
Four logic inputs activated by a voltage change from other equipment at the repeater site, causes the CAT-260 to activate event macros. One event macro will activate on the positive trigger edge while another macro will trigger on the trailing edge.

 

Output Switches
Six switches are available to control equipment at your repeater site. Controlled manually by DTMF commands or from a macro command, they can be made to turn ON, OFF or Momentarily change state, any time you choose

 

Repeater Control Channels
The CAT-260 has 42 remote control channels. Divided into groups, according to their function, they can be manually controlled through the repeater input. They are:

Port #1 Transmitter Enable Port #2 Transmitter Enable
Port #1 COR and CTCSS Enable Port #2 COR and CTCSS Enable
Port #1 COR or CTCSS Enable Port #2 COR or CTCSS Enable
Port #1 Turn on Delay Enable Port #2 Turn on Delay Enable
Port #1 DTMF Pad Test Enable Port #2 DTMF Pad Test Enable
Port #1 Courtesy Tone Enable Port #2 Courtesy Tone Enable
Port #1 DTMF Muting Enable Port #2 DTMF Muting Enable
Port #1 Timeout Enable Port #2 Timeout Enable
Scheduler Enable Port #2 Control Operator Enable
Time-of-Day Request Port #2 Macro Control Enable
Grandfather Clock Enable Port #2 Activity Check Enable
Grandfather Clock Sleep Enable Fan Control Enable
Repeater ID (Rest) Enable Repeater ID (Active) Enable
Squelch Tail Message Enable Transmitter Drop Message Enable
Timed Message #1 Enable Timed Message #2 Enable
DTMF Access Enable Switch Output #1 Enable
Forced DTMF Entry Enable Switch Output #2 Enable
Logic Input #1 Enable Switch Output #3 Enable
Logic Input #2 Enable Switch Output #4 Enable
Logic Input #3 Enable Switch Output #5 Enable
Logic Input #4 Enable Switch Output #6 Enable

 


CAT-260 System Diagram

CAT260 BLK

 

 Multi Port Operations
In this configuration the CAT-260 supports a repeater and three (3) transceivers. With the RLS-1000B Remote Link Switch board connected to port #2 of the CAT-260, three transceivers can be added to your repeater system. Three (3) of the CAT-260's user function output switches are assigned to control the RLS-1000B's transceiver interfacing.

 

CAT260RME1

CAT260RME3

CAT260RME2

CAT-260 mounted within optional RME-200 Rack Mount Enclosure

 

CAT-260 Specifications

Microcontroller Atmel ATxmega256A3BU
Memory Flash 256K, RAM 16K
Voice Synthesizer Texas Instruments MSP53C391N
DTMF Receivers Microsemi MT88L70 (One each per Port)
Logic Inputs Active High 3-15VDC 4K Input Impedance
Logic Output Switches Four switches at 40 volts/50ma per switch
Operating Temperature -15 to +55C
Input Power +9 to +15VDC at 50 mA
Size PCB 7.0" X 4.85"
FCC Part 15 Registered  

Ordering Information

 CAT-260  Repeater Controller Board, Wired & Tested $349.00
 ED-260W  Windows Editor $49.00
 RME-200  Rack Mount Enclosure $79.00